 Detailed Features
A Closer Look
Features
- 5000VA/3750W maximum output power capacity compatible with North American 208V/60Hz input voltage
- Supports full output at either 208V or 120V
- 3U rack/tower UPS installs in standard 19-in. rack enclosures with an installed depth of only 22.5 in.
- Protects sensitive networking equipment from blackouts, voltage fluctuations and transient surges
- Line-interactive automatic voltage regulation (AVR) corrects
208V nominal input from 167V to 260VAC back to usable 208/120V levels
without consuming battery power
- AVR circuits boost undervoltages by 12% and reduce overvoltages by 12%
- Network interfaces support simultaneous communications via USB, DB9 serial and SNMPWEBCARD slot
- Included PowerAlert UPS monitoring software supports safe
unattended shutdown, monitoring and control via local connected servers,
plus any number of additional servers over IP
- Communication ports support on-battery, low-battery,
power-restored, AC voltage, DC voltage, output current monitoring,
battery charge current, battery capacity, internal UPS temperature, AC
line frequency, timed inverter shutoff, activate self-test and load bank
output power control
- Built-in Emergency Power Off (EPO) interface with cable
- Sine wave output in AC and battery mode
- Expandable runtime with optional BP48V60RT3U external battery packs
- Half/full load runtime of 27/10 minutes with internal batteries
- Includes 11 output receptacles (2 L6-20, 1 L6-30 and 8 NEMA 5-15/20R)
- Ships with installed L6-30P input plug, supports user-supplied 50A replacement plug or hardwire input
- Integrated 8-bank switched PDU enables remote outlet management for load shedding or remote reboot of individual devices
- 3-stage metered LEDs provide current and battery charge level monitoring
- Utility power and voltage regulation LEDs provide at-a-glance power status information
- Front panel switches support self-test and alarm cancel functions
- Included adjustable mounting rails support installation in 4-post, 19-in. racks
- UPS ships fully assembled in full compliance with DOT
regulations—no time consuming connection of internal batteries is
required
- Supports 2-post rackmount installation with optional 2POSTRMKIT accessory
- Supports upright tower placement with optional 2-9USTAND accessory
- UL (USA), cUL (Canada), NOM (Mexico), TUV, FCC Class A (Emissions) listed
- 2-year manufacturer's product warranty; $250,000 Ultimate Lifetime Insurance
What You Should Know
 |
 |
Uninterruptible Power Supplies (UPS) - What Wattage is Best for You
The most important question you need to ask when you buy a UPS backup is
how much time you have to shut down or back up your data if the power goes
down. Obviously, if you purchase a UPS backup that lacks the muscle to sustain
your load in the event of a power outage, you’ve wasted your money. That’s
why our Editors have created a handy chart that illustrates the average
run time for UPS backups. |
 |
 |
Standard Electrical
Specification Terms
What Is A Joule? Or a Watt, Volt, or an Amp?Electronics and
Electricity, uses a wide range of terms to represent different kinds of measurement units.
Many you have seen every day, and others from time to time in product specifications. These
are all part of the International System of Units. Here is a short list of several common
terms your will see in our products and their meanings:
JOULE: One joule (symbol: J) is
defined as the amount of work done by electricity. Technically it is the work required to
continuously produce one watt of power for one second; or one watt second (W*s). One
kilowatt hour (a common electric company measure) equals 3,600,000 Joules (1W*s x 1,000 x 3600
seconds).
Using This Chart You Can Easily Calculate
The Wattage, Current (Amps), Ohms, and Voltage For A Device!
WATT: In terms of mechanical
energy, one watt (symbol: W or P) is a measure of energy used - this frequently results in heat, or
as in the case of a light bulb, the heat creates a glow, thus more heat equals more light.
Technically a Watt is the rate at which work is done when an object is moved at a speed of one meter
per second against a force of one newton. By the definitions of electric potential (volt) and
current (ampere), work is done at a rate of one watt when one ampere flows through a potential
difference of one volt - or simply A*V=W
AMP (Ampere): In practical
terms, the ampere (symbol: I) is the amount of electrical current passing through a conductor (a
wire). Technically it is a measure of the amount of electric charge passing a point per unit
time. Around 6.242 × 1018 electrons passing a given point each second constitutes one ampere. You
can figure out the Amps being use by dividing the Wattage by Voltage. A 100W light, in a
typical house (120V) uses 1.2A.
VOLT (Voltage): The volt
(symbol: V) is the unit of electromotive force measurement, commonly called "voltage".
Technically, the volt is defined as the value of the voltage across a conductor when a current of
one ampere dissipates one watt of power in the conductor. For example, if you know a TV uses
295 Watts and uses 2.45 Amps, you can calculate the voltage is 120 Volts.
OHM: The ohm (symbol: Ω
or R) is the unit of electrical impedance in AC, or, in the direct current case, electrical
resistance. It is the resistance of material to electrical current. The higher the
value, the higher the resistance, and the more voltage is required, and the more current used.
Most home speakers are low resistance, just 8 ohm. Technically, the ohm is defined as the
resistance between two points of a conductor when a constant of 1 volt is applied, and
produces in a current of 1 ampere.
DECIBEL: The decibel (dB)
is a logarithmic unit of measurement that expresses the magnitude of a physical quantity (usually
power or intensity) relative to a specified or implied reference level. The decibel is useful
for a wide variety of measurements (particularly acoustics and electronics). It has a number of
advantages, such as the ability to conveniently represent very large or small numbers, in a scaling
that roughly corresponds to the human perception of sound and light. It is frequently seen in
Home Theater Receivers to represent amplification or volume. Since it is based on a reference
level, it is not easily used by the non-engineer, but simply as a specification value. |
|
|
|
Power Protection Type:
Tidak ada komentar:
Posting Komentar